TC Encore Muzzleloader

TC Encore PeepRib Muzzleloader Sight- Our original PeepRib Aperture Sight for TC Encore, Pro Hunter, Triumph, Triumph Bone Collector, Impact and Omega combines a precision aperture sight with a scope mounting base. You can position a riflescope on and...

  The WGRS is an Aperture Sight that fits Thompson Center Arms Encore, Pro Hunter, Omega, and Impact. An aperture sight (aka peep sight), mounted as close to your eye as possible, removes a huge amount of aiming error by simply increasing the sight...

  A hardened steel, dual-purpose tool which taps out the forend wedge just enough so that it can be caught and pulled free with the claw end. It's also a nipple wrench that fits all T/C nipples that take #11 caps, except the T/C Scout. For more...

The NEW Lee Auto Prime hand priming tool is a fast, safe, and effective way of priming cases. Also recommended for priming the VariFlame II primer holders for muzzle loaders. Lee Auto Prime uses inexpensive Lee Hand Prime shell holders only (see below)...

TC Encore Pro Hunter Muzzleloader Front Sight .455 Green- Fiber Optic Ramp Style Front Sight fits the special 8-40 threads of the Encore Pro Hunter front sight mounting hole. .455" height measured from the top surface of the barrel to the top of the...

TC Encore Pro Hunter Muzzleloader Front Sight .455 Orange- Fiber Optic Ramp Style Front Sight fits the special 8-40 threads of the Encore Pro Hunter front sight mounting hole. .455" height measured from the top surface of the barrel to the top of the...

  Solid brass, the knurled end screws off for easy filling. Holds approximately 80 grains FFFFG Black Powder. Dispenses a small amount of priming powder. Each dispensed charge fills the flash pan of a T/C Flint Lock rifle one-half full. NOTE:...

T/C .50 cal Round Ball Bullets - Flat Rate Shipping*  For those hunters who prefer (or are required by law) to use patched round balls in their muzzleloader, T/C offers these precision swaged, pure lead round balls. Sized properly to work with any...

Encore Muzzle Loader Forend HardwareFor Factory Walnut and EABCO Laminate Muzzleloader Forends   All the hardware needed to attach the Encore Laminate or Factory Walnut Muzzle Loader forend. Includes the leaf spring rod retainer with screw, and...

Dead Center Duplex Bullets -   Duplex Dead Center Bullet - Shoots a .357 caliber Dead Center bullet from your 50 caliber muzzle loader. A seemingly crazy idea that seats a high BC .357 caliber Dead Center bullet into a sabot-within-a-sabot...

Dead Center BulletsMuzzleloaders are limited in velocity by the physics of the gun and the limitations of the components. The only place left to increase performance is through bullet design... Introducing the Dead Center Bullet. Dead Centers are...

  Small and light, this handy little short starter performs big. A solid aluminum shaft with a concave loading tip, attached to a rugged polymer palm saving knob, provides the hunter with a no-nonsense short starter which is all but...

Extreme Elite Bullets -  The Extreme Elite Bullet represents the "very best value" in an all-lead hunting and target bullet. It delivers outstanding accuracy with Encore and Omega 209X50 rifles. The 330 and 360 gr saboted bullets are optimum for the...

  A biodegradable all natural lubricant which contains no petroleum-based oil or additives. Reacts differently (chemically) to the combustion of black powder, producing far less “tar like” fouling. 5oz. tube ideally suited for easy application...

Encore Muzzle Loader Screws and WashersFor T/C Encore Muzzleloader Forends  The screws and washers needed to attach the Muzzle Loader forend. Includes two (2) forend screws with two (2) washers. These screws fit factory composite and/or wood as well...

  Solid brass body with steel jaws. This unique design allows the plunger spring to be locked in compressed position for easy loading, then released to keep #11 caps under tension for reliable dispensing. Holds up to 17 of the #11 Percussion...

 T/C Magnum .50 caliber QuickShot with three .50 caliber Mag Express Sabots with 240 grain XTP bullets. All you have to do is add your favorite black powder or Pyrodex charge and you're ready for the field. The .50 caliber QuickShot with (3) .50 cal...

Pro Hunter "FlexTech" Muzzle Loader Forend Screws and Washers The TC Factory Pro Hunter "FlexTech" forend for muzzle loaders has two screws of different length (2 washers also included). If you've lost one or both screws or washers, this kit supplies...

  This Breech Cleaning Brush is for cleaing up the threads around the removable breech plug. It’s long enough to reach into the threads in the barrel/receiver as well. For more Muzzle Loading Accessories Click Here!

  3 convenient muzzleloading ammo tubes. Use them as a handy way to carry spare sabots or Pyrodex pellets. These can also be cut or sized to accommodate your specific charge with sabot, converting each tube to a handy and speedy loading tube...

  Fits .54 and .56 calibers with 10-32 thread. Non-marring solid brass with deep grooves to hold patch securely. For more Muzzle Loading Accessories Click Here.

  This Thompson Center Pyrodex powder spout makes it easier to pour Pyrodex powder directly from the container into a powder measure. This spout is for the Pyrodex Powder Bottles Only. For more Muzzleloading Accessories Click Here.

  This Thompson Center powder spout makes it easier to pour black powder directly from the container into a powder measure. This spout is for the Black Powder Can Only.For more Muzzle loading Accessories Click Here. *Please Note: Custom and...

  For the .45 cal (10-32)This one really works! Threads onto a T/C ramrod and successfully removes stuck balls, bullets or shotgun wads from the bore. For more Muzzle Loading Accessories Click Here.