TriggerTech Diamond fits AR-15, Straight Flat Black TriggerAdjustable from 1.5 to 4 lbs. the TriggerTech "Diamond" AR-15 Trigger is an advanced shooter trigger replacement for the milspec AR-15 trigger. It gives you all of the advantages of FRT Friction...

Timney AR-10 Competition Trigger If you’re looking to get the most out of your AR-10 for your next competition then look no further, this is the trigger you need. With an incredibly smooth pull, a crisp feel, and reliability at every turn,...

Thread Protector fits Large Caliber 11/16 x 24 Blued (Black) Beautiful knurled blued thread protector in 11/16x24 thread with length of .625" and outside diameter of .820" Compatible with new TC ProHunter large caliber barrels (over 30 cal) like the 360...

Thread Protector fits Large Caliber 11/16 x 24 Stainless  Beautiful knurled stainless thread protector in 11/16x24 thread with length of .625" and outside diameter of .820" Compatible with new TC ProHunter large caliber barrels (over 30 cal)  

AccuWasher Gen 2 Muzzle Device Alignment The AccuWasher® Gen 2 Muzzle Device Alignment System is the ultimate solution for precise and repeatable muzzle device alignment. Unlike traditional crush washers, this mono-shim system is precision...

Encore Pro Hunter Speed Breech Plug (Original) - Originally introduced on muzzleloader barrels with the Pro Hunter label, the original Speed Breech combines engine piston style sealing rings with an O-ring and a quicker breechj plug removal system...

TC Encore ProHunter FX Speed Breech 3 Speed Beech 3 breech plugs require no tools, and spin out by hand for easy cleaning.  The TC Encore FX is the fixed version, which requires a specific FX Speed Breech 3 plug.  Replace your existing breech...

TC Encore Pro Hunter Trigger Spring Kit Do It Yourself Clean Up and Tune Up Kit That Also Lightens Trigger Pull Lighter Trigger/Sear Spring - Reduce Trigger Pull from 5.75 lbs to Aprox. 2.5-3 lbs* SPEEDLOCK Hammer Spring - Gives More Reliable Primer...

Colt AR15/M16 Upper Adaptor Offset BushingAdapt your Colt large pin upper to fit your small pin lower with this offset adapter bushing.  On the Colt AR15/M16, the front pin that joins the upper receiver to the lower receiver is larger than the...

SSK-50 Hammer Fits Original Contender and SSK-50 Receivers Fits SSK-50 firearm platforms May be compatible with TC Contender®, but due to their extreme dimensional variation, SSK cannot guarantee this. Please contact Smith & Wesson for...

JARD Match Grade Trigger for the CZ 457 This trigger takes the CZ 457 Trigger up into a new level of refinement. It comes Drop-In Ready.Sear engagement (take up) and over travel are adjusted and pre-set to optimum for whichever trigger weight you choose...

Long Action AICS Magazines  These single-stack, single-feed magazines for Long Action AICS mag wells are perfect for medium and long length cartridges. They're made by Accurate-Mag and they're built from steel, heat-treated and coated with a Teflon...

 YoDave CZ-452 Plus 10 Striker Spring Upgrade your worn or weak CZ-452 striker spring with this new 10 percent heavier striking spring for a more consistent primer strike and ignition. Also fits 453, 455, and 513 models. All benchrest...

YoDave CZ-455 Trigger Shim and Spring KitImproves the Trigger Pull of CZ-455, CZ-452 and BRNO Model 2, 4, and 5 Rifles This kit removes the creep and lightens the trigger pull weight by the use of shims and new springs. Kit includes 4 shims and 4 new...

Volquartsen Mk IV and Mk IV 22/45 Competition Kit Also Converts Mk IV and Mk IV 22/45 Pistols to Eliminate the Magazine Disconnect   Trying to figure out which parts are needed to take the Ruger MKIV and 22/45 to the next level? Look no...

Volquartsen HP Action Kit for 10/22  This kit consists of Volquartsen upgrade parts including: Target hammer (including shims and bushings), hammer spring, target disconnector, target sear and target trigger (including polished plunger and spring)...

Thread Protector, 1/2x28, .820 Dia., Stainless, Knurled A stainless knurled thread protector to protect and beautify the threaded muzzle of your barrel. Recessed threads on the back side assure a tight and seamless fit. Beautifully knurled for handy...

SSK-50 Frame, Lynx Sided The Original Contender/SSK-50® design is back in production, thanks to the SSK Firearms company. It has been a long time and a big challenge to re-tool for independent production of this classic single shot action. This new...

SSK-50 RECEIVER, Flat-Sided The SSK-50 Receiver is the modern revival of the original Contender design, now produced with advanced materials and precision manufacturing. This flat-sided stainless steel receiver is compatible with TC G1/G2 barrels, grips,...

Thread Protector AR-10 Heavy Profile 5/8X24 Stainless- Protect and beautify your Heavy Profile AR-10 muzzle threads with this beautiful knurled stainless thread protector. Standard 5/8X24 thread with a length of .625 inch and .930" diameter, it fits...